VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  THC Vape  /  THC Vape merchandising — steps
THC vape products · first-time buyers

THC Vape merchandising — steps

There is no shortage of suppliers quoting THC vape. The scarce thing is a supplier who will tell you which SKU to drop. We have been shipping THC vape products long enough to know that the honest answer is usually a shorter list, and that is the answer we give.

Published 12 August 2026  ·  VapeWholesaleHub  ·  Reading time 5 min

THC Vape merchandising — steps configuration from a production run, photographed before packing.
THC Vape merchandising — steps configuration from a production run, photographed before packing.
Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.
Finish and assembly detail checked against the approved reference sample.
Finish and assembly detail checked against the approved reference sample.

Unit price versus landed cost

Buyers come to us for THC vape after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for first-time buyers.

Payment terms for new accounts are normally a deposit with the balance against the bill of lading. Established buyers on a repeat schedule can move to terms after three clean shipments.

We publish a realistic band of 3.19 to 10.03 per unit for standard configurations at 60 units. Below that band you are buying a lighter specification; above it you are paying for finish, packaging or a smaller run.

Getting the carton there intact

We ship from Shenzhen and Guangzhou: air express for samples and part loads, sea freight for volume. Typical production lead time is 12 working days after artwork approval, plus transit. We quote both routes so you can see the trade-off instead of guessing at it.

For repeat buyers we hold a shipping schedule rather than shipping on request. A fixed weekly cut-off means your reorder lands before the shelf empties instead of after.

For first-time buyers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

What your market will ask for

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

Advertising rules are stricter than product rules in most markets. Claims about cessation, health or comparative performance should stay off packaging and off your product pages unless your legal team has signed them off.

  • Artwork proof plus physical dummy for custom packaging
  • Specification locked in writing before production starts
  • Consolidated or split shipping, quoted both ways
  • Mixed SKU cartons to spread first-order risk
  • Standing reorder schedule with a fixed cut-off
  • Document pack prepared per destination market

Where defects actually come from

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

Flavour drift between batches is the quiet killer of repeat orders. We retain a sealed reference sample from every run so a complaint six weeks later can be compared against what actually left the building.

Specification summary

Typical specification for this category
Volume1.0 ml
HardwareCotton core
ThreadProprietary pod
AirflowAdjustable
WindowSide window
PackagingTube
Minimum order300 units per SKU, mixed cartons allowed
Lead time25 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

Can we order samples before committing?

Yes. Sample orders are shipped by air express and the cost is credited against your first production order above 60 units. We would rather you handle the sample than approve a specification from a photograph.

How long does production take?

Around 12 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

Related reading

Need a quotation on THC vape products?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on THC vape products

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us